Hi.
After upgrate to Ranorex v3.3 the "AnyCPU" platform is no longer available for new projects. Same with v3.3.1.
For the old projects there are still "AnyCPU", "x86" and "x64" but if I create a new project I can only select x86.
Please explain.
AnyCPU is not available
- Support Team
- Site Admin
- Posts: 12145
- Joined: Fri Jul 07, 2006 4:30 pm
- Location: Houston, Texas, USA
- Contact:
Re: AnyCPU is not available
Hi,
This should not be the case. We haven't heard about such a problem with version Ranorex 3.3.
Are you able to run the 64 bit version of Ranorex Spy?
Can you send us a Ranorex Snapshot file of your application?
Following link will show you how to generate a snapshot file:
Creating Ranorex Snapshot Files
Thanks,
Markus
Ranorex Support Team
This should not be the case. We haven't heard about such a problem with version Ranorex 3.3.
Are you able to run the 64 bit version of Ranorex Spy?
Can you send us a Ranorex Snapshot file of your application?
Following link will show you how to generate a snapshot file:
Creating Ranorex Snapshot Files
Thanks,
Markus
Ranorex Support Team
Re: AnyCPU is not available
A snapshot created with 64-bit version of Spy is sent to the support mail.
We also tried to create a new solution but all we can choose is x86 for a project.
We also tried to create a new solution but all we can choose is x86 for a project.
- Support Team
- Site Admin
- Posts: 12145
- Joined: Fri Jul 07, 2006 4:30 pm
- Location: Houston, Texas, USA
- Contact:
Re: AnyCPU is not available
Hi,
The snapshot shows a technology limitation warning "Failed to load assemblies ...", could it be that Ranorex was not properly installed, did you use the setup.exe file for the installation?
If not please reinstall Ranorex with the setup.exe file.
Did you already checked the points listed on the link which was shown by the technology limitation warning? General Troubleshooting
Can you send us your project if none of the points helped to solve the problem?
Thanks,
Markus
Ranorex Support Team
The snapshot shows a technology limitation warning "Failed to load assemblies ...", could it be that Ranorex was not properly installed, did you use the setup.exe file for the installation?
If not please reinstall Ranorex with the setup.exe file.
Did you already checked the points listed on the link which was shown by the technology limitation warning? General Troubleshooting
Can you send us your project if none of the points helped to solve the problem?
Thanks,
Markus
Ranorex Support Team
Re: AnyCPU is not available
Hi Markus,
Our problem is that when we upgraded (from setup.exe) we lost the possibility to select "AnyCPU" in ranorex and therefore we get those "failed to load assemblies".
I can force the project to use "AnyCPU" by manually go and edit the *.csproj file but I dont think that should be necessary.
Also we tested to install a ranorex demo on a clean computer and that also ended up to display "x86" platform only.
Clearly something must have changed between 3.2 and 3.3
Our problem is that when we upgraded (from setup.exe) we lost the possibility to select "AnyCPU" in ranorex and therefore we get those "failed to load assemblies".
I can force the project to use "AnyCPU" by manually go and edit the *.csproj file but I dont think that should be necessary.
Also we tested to install a ranorex demo on a clean computer and that also ended up to display "x86" platform only.
Clearly something must have changed between 3.2 and 3.3
- Support Team
- Site Admin
- Posts: 12145
- Joined: Fri Jul 07, 2006 4:30 pm
- Location: Houston, Texas, USA
- Contact:
Re: AnyCPU is not available
Hi Kaj,
Thanks,
Markus
Ranorex Support Team
I agree there are many changes in 3.3, but we haven't heard about such a problem before, so we also have to figure out what could be the reason for this behavior, therefore it would help us if you can send us one of your Ranorex test solutions where we can see the problem.I can force the project to use "AnyCPU" by manually go and edit the *.csproj file but I dont think that should be necessary.
Clearly something must have changed between 3.2 and 3.3
Thanks,
Markus
Ranorex Support Team
Re: AnyCPU is not available
Files have been mailed. Hope it can help.
- Support Team
- Site Admin
- Posts: 12145
- Joined: Fri Jul 07, 2006 4:30 pm
- Location: Houston, Texas, USA
- Contact:
Re: AnyCPU is not available
Hi Kay,
Thanks for the files.
This is by design, we changed it in one of the newer versions, if you want to add another configuration/platform you can manually create one.
To add a new one you have to click on Build -> Edit configurations/platforms, then you have to click on the platform combobox and on "Edit", then you should see a window where you can add a new platform. Regards,
Markus
Ranorex Support Team
Thanks for the files.
This is by design, we changed it in one of the newer versions, if you want to add another configuration/platform you can manually create one.
To add a new one you have to click on Build -> Edit configurations/platforms, then you have to click on the platform combobox and on "Edit", then you should see a window where you can add a new platform. Regards,
Markus
Ranorex Support Team
You do not have the required permissions to view the files attached to this post.